Your position: Home / Brands / MUZISHARE
  • Description
    Technical parameters:
    • Rated output power: 15W + 15W (RMS triode working condition)                   
                                        35W + 35W (RMS ultra-linear working condition)
    • Harmonic distortion: 1% (1KHZ)
    • Frequency response: 10HZ ~ 50KHZ (-1.5DB)
    • Input Sensitivity: 200mV Input impedance: 100KΩ
    • SNR: 88DB 
    • Output Impedance: 4Ω, 8Ω
    • Net weight: 18.5kg
    • Package weight: 25kg
    • Power consumption: 230W
    • Tube: Shuguang 12AX7×2 (they can be replaced by 12AX7EH,ECC83,
                                                  E83CC,CV4004,ECC803,5751)                                                Shuguang12AU7×2 (12AU7EH,ECC82,5814,6189, CV4003)
               Shuguang EL34×4 ( 6CA7)
    • Dimension:350×315×185mm
    • Voltage:110/120v or 220/235v±5%(50Hz)
    • Working conditions: Temperature: 0 ºC~ 40 ºC Humidity: 20% to 80%
    • Storage conditions: Temperature: -20 ºC ~ 70 ºC Humidity: 20% to 90


    • Handmade, using scaffolding welding
    • using two high quality and wide frequency response EI output transformer
    • Using a customize EI power transformer
    • Use 2X12AX7 and 2X12AU7 as pre-amp tube, use 4XEL34 as push pull power amp,providing the triode connnection and ultra-linear connection modes.The triode connection mode is more suitable for the voice and the sound is more soft, delicat as well as nature. The ultra-linear connection is suitable for the big scence, the sound is open and lively.
    • There is a power tube current control button and an electric meter dial.
    • Infrared remote control function
    • Power Mute delay function
    • Selection of Japanese high-grade ALPS motor potentiometer.
    • Easy installation of the plug-type vacuum tube shield




    Tube Amplifier Precautions

    1. Tube amp must connected with speakers before turning ON. Strictly prohibit send signals to amp without connected loads(speakers) or load short circuit when the switch is ON.

    2. Too high or too low power supply voltage does irreversible harm to the amp,preferably less than 5% of the specified voltage. If your mains voltage exceeds this value, often best to use with the AC power supply.

    3. Temperature is higher when tube amps working, placing attention to ventilation, cooling. 

    4. In the boot or just shut down for a period of time (within 30 minutes) Do not spill liquid on the tubes.

    5.  You should take about 100h time to operate the amp.RUN-IN to the amp gives it's best and stable sound.so during the first 100h use time the sound maybe is not the best,you can also use your own run-in method. 

    6. If you donot sure how to plug the tubes, please contact us before try it

    Speakers connection

    All tube amplifier used with stereo mode:  L(left) and R(right) speakers.
    Normally there are 6 speaker cable connectors: +8L, +4L, -0L, -0R, +4R, +8R 

    Example: +8L and -0L are for connecting with your Left 6-8ohms speaker 
    -0R, +4R is for 
    connecting with your Right 4ohms speaker 


    Tube amplifier guaranty :

    Tube amplifier Guarantee:  6 months for tubes sold with amplifier, 1 year for the amplifier and PSVANE tube

MUZISHARE X5 EL34 Tube Amplifiers

    Please select the information you wantX
  • Voltage:
(13 available)

Copyright © 2020-2035 MySite Ltd. All Rights Reserved.